EA3AIL

Digital workshop · Live audio

Digital mode decoder

Connect your receiver's audio output to the computer's input (or use the audio of a browser tab running a web SDR), pick the mode and watch the text appear. The audio never leaves your computer.

Audio source

Stopped. Choose the audio source and the mode, then press “Start”.

Mode

Waterfall

Click the waterfall on top of a signal to tune it. With “Automatic” the decoder finds the strongest signal on its own.

Output · FT8

How to connect the radio

  • With a cable: headphone or data (ACC, DATA) output of the transceiver into the computer's line or mic input. If the radio has USB with a built-in sound card (IC-7300, FT-991, TS-590...), select it under “Input device”.
  • A good level is between −40 and −15 dBFS with band noise only. If the meter shows “!”, the input is clipping: turn down the radio volume or the input level.
  • For FT8, FT4, PSK31 and RTTY, put the radio in USB (upper sideband) with a wide 2.7–3 kHz filter. For CW, use CW or USB with the tone around 600–800 Hz.
  • FT8 and FT4 work in 15 and 7.5 second periods timed by the clock: your computer's clock must be right to within a second (automatic time sync on).
  • No radio? Open a web receiver (for example a KiwiSDR, or the Radio page on this site) in another tab, tune 14.074 MHz USB and use the “Browser tab” source.

The modes

FT8 HF · 6 m

The most used mode on HF. Every 15 s the page decodes everything between 200 and 3000 Hz. Usual frequencies (USB): 1.840 · 3.573 · 7.074 · 10.136 · 14.074 · 18.100 · 21.074 · 24.915 · 28.074 · 50.313 MHz.

FT4 HF · contests

FT8's fast sibling, for contesting. Usual frequencies (USB): 3.575 · 7.0475 · 10.140 · 14.080 · 18.104 · 21.140 · 24.919 · 28.180 MHz.

CW HF · VHF

Telegraphy. The decoder finds the tone and the speed by itself; if there are several signals, click the one you want. Works best with a narrow filter on the radio (250–500 Hz).

RTTY HF · weather

Radioteletype. Amateurs use 45.45 baud and 170 Hz (14.080–14.099 MHz); the German weather service DWD sends 50 baud, 450 Hz (10100.8 and 14467.3 kHz). If you get gibberish, try “Reverse”.

PSK31 HF

Very narrow keyboard chat (60 Hz). Usual frequencies (USB): 3.580 · 7.040 · 14.070 · 21.070 · 28.120 MHz. Click the centre of the trace.

FreeDV HF

Open digital voice using the Codec2 codec or the RADE neural network. The page recognises the signal and reports its centre, width and carrier spacing so you know which mode it is; to hear the voice you need the FreeDV application. Frequencies: 3.625 · 7.177 · 14.236 MHz (USB).

SELCALL HF aviation · PMR

Selective calling. On aeronautical HF (Shanwick 2.872 · 5.649 · 8.879 MHz, USB) aircraft get a four-letter SELCALL such as “AB-CD”. On professional VHF/UHF, 5-tone CCIR, ZVEI or EEA sequences.

ACARS VHF 131 MHz

Aircraft messages (position, fuel, arrival time...). Receiver in AM, wide filter, on 131.525 · 131.725 · 131.825 MHz (Europe) or 129.125 · 130.025 · 131.550 MHz (Americas). Turn off noise reduction.

POCSAG VHF · UHF

The pager protocol. The audio must come from an FM receiver without filtering or de-emphasis (discriminator output, or an SDR in NFM with 12 kHz bandwidth). Speed and polarity are detected automatically.

DTMF VHF · phone

Telephone keys: two tones at once for each key. Used to control repeaters, links (EchoLink, IRLP) and switchboards.

Everything happens in your browser: the audio is not sent anywhere or stored. The microphone permission is only needed so the page can read the audio input.

FT8 and FT4: JavaScript port of ft8_lib by Kārlis Goba (YL3JG), MIT licence; the protocols are by K1JT, K9AN and G4WJS (WSJT-X). PSK31 Varicode: G3PLX. The other decoders are by EA3AIL.